correlation to ASTM E They are also required to meet reporting and recordkeeping requirements for quality control. Seven years after the final rule is . The ASTM D (small chamber) and ASTM E (large chamber) test methods are used by the composite wood products industry to measure emissions of. ASTM E – Standard Test Method for Determining. Formaldehyde Concentrations in Air and Emission. Rates from Wood Products Using a.

Author: Zulkikora Tauzil
Country: Cuba
Language: English (Spanish)
Genre: Technology
Published (Last): 11 October 2005
Pages: 259
PDF File Size: 16.95 Mb
ePub File Size: 19.87 Mb
ISBN: 233-6-12059-332-7
Downloads: 93083
Price: Free* [*Free Regsitration Required]
Uploader: Doutilar

Historical Ast s – view previous versions of standard. This test method measures the formaldehyde concentration in air and emission rate from wood products containing formaldehyde by the use of a large chamber under specific test conditions of temperature and relative humidity, or conditions designed e1333 simulate product use.

This method employs a single set of environmental conditions but different product loading ratios to assess formaldehyde concentrations in air and emission rates from certain wood products.

CARB Testing of Formaldehyde Emissions for Composite Wood Products

The conditions controlled in the procedure are the conditioning of specimens prior to testing, exposed surface area of the specimens in the test chamber, test chamber temperature and relative humidity, number of air changes per asym, and air circulation within the chamber. At the end of a specified time period in the test chamber, the air is sampled, and the concentration of formaldehyde in the air and emission rate are determined.

  LIBRO PAPAITO PIERNAS LARGAS JEAN WEBSTER PDF

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

This test method provides a standard means of testing typical product sizes, such as 1. This test method employs a single set of environmental conditions but different product loading ratios to assess formaldehyde concentrations in air and emission rates from certain wood products. Conditions controlled in the procedure are as follows:. Care e13333 be exercised in the extension of the results to formaldehyde concentrations in air satm emission rates from products under different conditions of air change rate or loading ratio, or both.

The concentration in air and emission rate is determined in a large chamber under specific test conditions of temperature and relative humidity.

The general procedures are also intended for testing product combinations at product-loading ratios and at air-exchange rates typical of the indoor environment 1. The average concentration and emission rate reported, thus, will not provide information on higher or lower emitting panels in the test lot. When this test method is used for aastm other than newly manufactured panel products after original application, installation or usethe method of packaging and shipping the product for testing shall be described in the test report.

  ANTIGONA SRPSKI PDF

If another analytical procedure is used to determine the quantity of formaldehyde in the air sample, that procedure shall give results of equivalent or greater accuracy and precision than the adapted chromotropic acid procedure. The test report shall note the analytical procedure employed.

Formaldehyde Standards for Composite Wood Products Act – Wikisource, the free online library

A more sensitive analytical procedure is recommended for testing wood panel products where formaldehyde concentrations in air are anticipated to be at or below this level. DNPH is recognized as such a method. Measurement results are also used for comparing concentrations in air and emission rates from different wood products 2 and for determining compliance with product standards. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Conditions controlled in the procedure are as follows: Link to Active This link will always route to the current Active version of the standard.