2SC datasheet, 2SC circuit, 2SC data sheet: HITACHI – Silicon NPN Epitaxial,alldatasheet, datasheet, Datasheet search site for Electronic. 2SC Datasheet, 2SC NPN Low Frequency Transistor, buy 2SC Transistor. ST 2SC NPN Silicon Epitaxial Planar Transistor. Low frequency amplifier applications. The transistor is subdivided into three group, B, C and. D according to.
|Published (Last):||27 December 2011|
|PDF File Size:||15.4 Mb|
|ePub File Size:||16.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
Log in or Sign up. In or Around the Motor City. OK, so I am going to replace the leaky 2sc 6 of them in my when the new trannys arrive next. I ordered the 2sc as a replacement from MCM. I read a thread on this forum that stated something to the effect that the 2sc has “opposite basing” than the 2sc Then a similiar thread mentions to “put them in backwards”.
The post was made by someone who is well respected and very experienced in this forum, so this is my reasoning for questioning what I have found in the data sheets. So looking at the data sheets I am not seeing it. It looks like a direct drop in. Not backwards, or whatever: I really want to be sure before I put these things in.
Yankee DogMar 14, Yankee DogMar 15, Trannys are in 2sc and it sounds a little sharper, and clearer if that means anything. Am Datasheet hearing more separation or is just because of less noise? I understand now why I was confused on how to place the transistors. On one side, the transistors go in like normal.
On the other side the trannys are basically a mirror of the first side preamp board. Sorry it’s hard to describe, but in a way, they do go in backwards sort of. Luckily the board was labelled E C B so Datxsheet just installed them keeping track of that.
Now I’m just waiting for my caps to arrive so I can breath more solder fumes. Some new-production 2SC’s have the same basing as the 2SC, but those new devices are not installed in vintage gear.
Fred LongworthMar 16, I did pay attention to the circuit board with the location of E C B 2sc45 put the legs of the 2sc in 2sc4458 apropriate holes, and unit is working fine, but, it looks like I’ll be pulling them. I assume that as long as I pay attention to E C B, it will keep me out of trouble like when installing the 2sc when I install the 2sc What about the data sheets I have posted?
To me it looks like they are the same. Is that what you mean by “Some new-production 2SC’s have the same basing as the 2SC, but those new devices are not installed in vintage gear”? The original 2sc does look different.
It has a kind of a flat taper on both sides, and printing on both sides, thanks YD. Yankee DogMar daatasheet, The original 2SC was made by Hitachi, and installed in a funny-looking rectangular package with a little “roof” on the top that slopes down from 2sc58 to back. These were based BCE reading left to right. At the time of manufacture, these were considered an excellent choice for a low-noise, small-signal transistor — daatsheet were used widely.
Unfortunately, they began to leak and generate noise and operating-point errors. Datxsheet few years ago, “new generation” 2SC’s began appearing. I consider many of these “new 2SC’s” to be counterfeits, i.
I chose it because in the spec manual it was called out as a 2sc48 small-signal device with a bandwidth not 2ac458 to the 2SC, and because the 2SC was used in many machines I encountered — and the device never seemed to fail. By the early ‘s, the 2SC had proved itself as a wonderful small-signal, low-noise transistor, again with an acceptable bandwidth, so I began using it as a replacement for the 2SC It works fine as a basic, small-signal transistor, and is fine for many applications.
I would never stick it in a low-noise circuit. In transistor selection, like many other aspects of electronics, the devil is in the details. Fred, thanks for the detailed information.
The 2sc’s arrived today and they are installed. Things are working and sounding fine.
Valley of Heart’s Delight. Yankee DogMar 17, EchoWarsMar 17, So, should 2SC’s of any age be replaced datashset they are found? I found a few in my X John. HyperionMar 17, They simply aren’t to be trusted. I replace them wherever I find them. EchoWarsMar 18, Thank you for the update – I found 2 – they looked so odd I checked up on them – particularly here on AK, and found them pretty much regarded as the spawn of the devil himself.
I used BC as the datawheet in my X – they work just fine. The old ones are now in my ‘rogues gallery’ Thanks again EW: HyperionMar 18, AndymanJan 4, Try the 2SCs you have. The issue here is not so much the noise level of the transistor, but the fact they need to be matched to datashedt other in vatasheet situation. I’m trying to buy some 2SC transistors from Digikey or Mouser, but am not having any success at all with this part number to replace my 2SCs can anyone recommend an alternate, or, better still the correct Digikey part?
You must log in or sign up to reply here. Share This Page Tweet. Your name or email address: Do you already have an account? No, create an account now. Yes, my password is: